Honda Fit/Jazz - CVT System Description - Electronic Controls (L12A/L13A CVT)
Bombardier ATVs Service ManualsHigh Quality Online manuals, fast download
CVT System Description - Electronic Controls
Electronic Control System
PCM Electrical Connections-6-position CVT
Electronic Control System (cont'd)
PCM Electrical Connections-6-position CVT +7 Speed Mode
PCM Inputs and Outputs
Terminal Number | Wire Color | Signal | Description | Measuring Conditions/Terminal Voltage |
---|---|---|---|---|
A2 | YEL/BLK | IGP2 | Power supply circuit from main relay | With ignition switch ON (II): Battery voltage With ignition switch OFF: 0 V |
A3 | YEL/BLK | IGP1 | Power supply circuit from main relay | With ignition switch ON (II): Battery voltage With ignition switch OFF: 0 V |
A4 | BRN | PG2 | Ground | |
A5 | BLK | PG1 | Ground | |
A10 | GRN/BLK | SG2 | Sensor ground | |
A11 | GRN/WHT | SG1 | Sensor ground | |
A18 | BLU/WHT | VABS | Vehicle speed sensor signal input | With ignition switch ON (II): About 5 V With ignition switch OFF: 0 V |
A20 | YEL/BLU | VCC2 | Power supply circuit for sensors | With ignition switch ON (II): About 5 V With ignition switch OFF: 0 V |
A21 | YEL/RED | VCC1 | Power supply circuit for sensors | With ignition switch ON (II): About 5 V With ignition switch OFF: 0 V |
A23 | BRN/YEL | LG2 | Ground | |
A24 | BRN/YEL | LG1 | Ground |
Terminal Number | Wire Color | Signal | Description | Measuring Conditions/Terminal Voltage |
---|---|---|---|---|
B7 | GRN/WHT | DN LS + | CVT driven pulley pressure control valve power supply positive electrode | With ignition switch ON (II): Pulsing signal |
B11 | RED/WHT | M IND | M indicator control (6-position CVT +7 Speed Mode) | When 7-speed manual shifting mode is selected: About 6 V In other than manual shifting mode: 0 V |
B12 | LT GRN | S IND | S indicator control (6-position CVT +7 Speed Mode) | In the S position: About 6 V In other than the S position: 0 V |
B16 | YEL | SC LS + | CVT start clutch pressure control valve power supply positive electrode | With ignition switch ON (II): Pulsing signal |
Electronic Control System (cont'd)
PCM Inputs and Outputs (cont'd)
Terminal Number | Wire Color | Signal | Description | Measuring Conditions/Terminal Voltage |
---|---|---|---|---|
B19 | LT GRN/RED | S-DN | Downshift switch signal input (6-position CVT +7 Speed Mode) | With ignition switch ON (II): Downshift switch pressed: 0 V Downshift switch released: About 5 V |
B20 | YEL | S-UP | Upshift switch signal input (6-position CVT +7 Speed Mode) | With ignition switch ON (II): Upshift switch pressed: 0 V Upshift switch released: About 5 V |
B24 | BLU/WHT | DR LS+ | CVT drive pulley pressure control valve power supply positive electrode | With ignition switch ON (II): Pulsing signal |
Terminal Number | Wire Color | Signal | Description | Measuring Conditions/Terminal Voltage |
---|---|---|---|---|
C1 | PNK/BLK | DN LS - | CVT driven pulley pressure control valve power supply negative electrode | With ignition switch ON (II): Pulsing signal |
C3 | BRN | CVT PG2 | Ground | |
C5 | BLK | CVT PG1 | Ground | |
C6 | GRN/BLK | SOL INH | Inhibitor solenoid control | With inhibitor solenoid ON (II): Battery voltage With inhibitor solenoid OFF: 0 V |
C7 | RED/BLU | NDR | CVT drive pulley speed sensor signal input | With ignition switch ON (II): 0 V or about 5 V With engine at idle in the N position: About 2.5 V |
C8 | PNK/BLU | SC LS - | CVT start clutch pressure control valve power supply negative electrode | With ignition switch ON (II): Pulsing signal |
C9 | BLU/WHT | ATP S | Transmission range switch S position input | In the S position: 0 V In other than the S position: About 5 V |
C10 | WHT | ATP R | Transmission range switch R position input | In the R position: 0 V In other than the R position: About 10 V |
C11 | BLU | ATP L | Transmission range switch L position input | In the L position: 0 V In other than the L position: About 10 V |
C12 | LT GRN | ATP NP | Transmission range switch P and N positions input | In the P and N positions: 0 V In other than the P and N positions: About 5 V |
Terminal Number | Wire Color | Signal | Description | Measuring Conditions/Terminal Voltage |
---|---|---|---|---|
C13 | YEL | M-SW | Main switch (7 Speed Mode) signal input (6-position CVT +7 Speed Mode) | In the 7 Speed Mode: 0 V Released the 7 Speed Mode: About 5 V |
C15 | WHT | NDN | CVT driven pulley speed sensor signal input | With ignition switch ON (II): 0 V or about 5 V With engine at idle in the N position: About 2.5 V |
C16 | GRN/YEL | DR LS - | CVT drive pulley pressure control valve power supply negative electrode | With ignition switch ON (II): Pulsing signal |
C20 | PNK | ATP D | Transmission range switch D position input | In the D position: 0 V In other than the D position: About 5 V |
C22 | WHT/RED | VEL1 | CVT speed sensor signal input | With ignition switch ON (II): 0 V or about 5 V With driving (front wheels rotating): About 2.5 V |
Terminal Number | Wire Color | Signal | Description | Measuring Conditions/Terminal Voltage |
---|---|---|---|---|
E8 | BLU/WHT | LED A | Shift indicator control (6-position CVT +7 Speed Mode) | With ignition switch ON (II) and not in the 7 Speed Mode: About 5 V In the 7 Speed Mode
|
E9 | YEL/BLK (KE,KG,KR models) | IG 1 | Power supply circuit | With ignition switch ON (II): Battery voltage With ignition switch OFF: 0 V |
BLK/YEL (KK,KQ,KT,KU models) | ||||
E11 | PNK | D IND | D indicator control | When ignition switch is first turned ON (II): About 6 V for 2 seconds In the D position: About 6 V |
E13 | BLU/RED | SLC | Shift lock control | With ignition switch ON (II), in the P position brake pedal pressed, and accelerator pedal released: Battery voltage |
E20 | GRN/BLK | LED C | Shift indicator control (6-position CVT +7 Speed Mode) | With ignition switch ON (II) and not in the 7 Speed Mode: About 5 V In the 7 Speed Mode
|
E21 | RED/WHT | LED B | Shift indicator control (6-position CVT +7 Speed Mode) | With ignition switch ON (II) and not in the 7 Speed Mode: About 5 V In the 7 Speed Mode
|
E22 | WHT/BLK | BK SW | Brake pedal position switch signal input | Brake pedal pressed: Battery voltage Brake pedal released: 0 V |
E23 | RED/WHT | K-LINE | Communication line PCM-to-DLC | With ignition switch ON (II): Battery voltage |
E29 | BRN | SCS | SCS terminal signal input | With ignition switch ON (II)
|
Circuit Diagram-6-position CVT
Circuit Diagram-6-position CVT +7 Speed Mode
Bombardier ATVs Service ManualsHigh Quality Online manuals, fast download