DIY     OBD-II Codes     Fix your Car     Repair Manuals     -Forum-

Advertisement  [ ? ]

Site Links

Troubleshoot Electronic Instrument Cluster


electronic instrument cluster

Electronic instrument clusters are used on many late model vehicles to display speed, fuel level, engine rpm (tachometer) and other gauge readings and warning lights.

One thing all electronic instrumentation shares in common regardless of make or model is the need for proper voltage and grounding. Most instrument clusters require a minimum operating voltage of 10 volts. If your electronic instrument panel is acting strangely, displaying weird or broken characters, not reading accurately or is displaying nothing at all, the first things you should check are the instrument cluster fuse, the presence of battery/ignition voltage at the cluster harness and the continuity of the cluster ground.

ELECTRICAL FAULTS

Replacing a blown fuse doesn't fix a dead cluster. It may temporarily restore power, but until you find out why the fuse blew you have only treated the symptom, not the cause. If a fuse blows again as soon as you replace it, it is a pretty good indication that the cluster or wiring harness is shorted. Disconnect the wiring harness from the cluster and check for a grounded power circuit with an ohmmeter before condemning the cluster.

The presence of battery/ignition voltage at the instrument cluster wiring harness should be checked with a voltmeter rather than a test light because you can't always judge low voltage by the brilliance of a simple 12 volt test light. Electronics are very sensitive to voltage levels, and 9.5 volts might not be enough for a cluster that requires a minimum of 10.0 volts to operate correctly.

To check the voltage, look up the wiring diagram in a shop manual (or get a wiring diagram from the http://www.crxsi.com/library/oemwebsites.htmOEM service website or AlldataDIY), then pull the connector off the back of the cluster and probe the appropriate pin(s) with your voltmeter with the ignition on. If you do not find normal battery voltage, you will have to trace the problem using the wiring diagram.

If the instrument cluster appears to be working normally (gauges reading normally), but the cluser is not lighting up, the fault could be a bad headlamp switch or interior lights dimmer switch (if separate from the headlamp switch).

A good ground connection is also extremely important. The presence of voltage at the cluster harness won't make the cluster work if there is a bad ground connection. Since the instrument cluster is mounted in a plastic dash, a separate ground wire or ground circuit through the wiring harness is usually needed to complete the power circuit. Refer again to the wiring diagram to find the ground path, and then check it with your ohmmeter. Do not use a self-powered test light because it cannot measure resistance (any resistance will lower circuit voltage).

INSTRUMENT CLUSTER NEED ACCURATE INPUTS

Another essential element all electronic instrument clusters require is accurate input from vehicle sensors. The speedometer, tachometer, fuel level, oil pressure, voltage and temperature gauges obviously cannot function correctly if there is a problem with the corresponding sensor or its wiring circuit.

If everything on an electronic instrument cluster seems to work okay except for one gauge that continually reads high, low or erratic, there is a high probability the problem is not in the cluster electronics but in the sending unit, sensor or wiring (especially if the gauge illuminates normally).

If one or more gauge display do not light up, however, or flicker, the problem is likely in the instrument cluster itself.

Once again you will need to refer to a wiring diagram to check continuity between the cluster wiring harness and the various sending units and sensors.

ELECTRONIC INSTRUMENT CLUSTER QUICK CHECK

One way to quick check electronic gauges is to go directly to the sending unit or sensor and ground it. In most cases, grounding will cause the gauge to read maximum, telling you there is nothing wrong with the electronics or wiring. The problem is in the sensor or sending unit.

INSTRUMENT CLUSTER SELF-CHECKS

When you first turn the ignition on, some instrument clusters go through a short self-check procedure during which all the display segments and warning lights come on for a bulb check. Watch for any dark segments or indicators that fail to illuminate.

Self-check procedures vary a great deal from one vehicle to the next, but on some applications you can run a self-check diagnostic by pressing certain display buttons. Look in your owners manual for instructions on how to run an instrument cluster self-check (if provided). This information can also be found at the OEM service information websites or via AlldataDIY.

Below are a two examples of instrument cluster self-diagnostic procedures that are available on some cars:

INSTRUMENT CLUSTER DIAGNOSIS PROCEDURE: LATE MODEL FORD MUSTANG

On 1999 and later Ford Mustangs, the instrument cluster has a built-in self-diagnostic mode that can be accessed by pressing and holding the instrument cluster SELECT/RESET button. Insert the ignition key and turn to the RUN position (but don't crank or start engine). Continue to press and hold the SELECT/RESET button (for 5 seconds) until the word TEST is displayed by the odometer.

Release the SELECT/RESET button within three seconds after the word TEST is displayed to begin the self-diagnostic mode.

Now every time you press the SELECT/RESET button, you will advance through a series of self-diagnostic checks and displays until any fault codes that are present for the instrument cluster will be displayed. Keep going and the unit will cycle through a series of gauge (GAGE) displays and self-checks.

To exit the instrument cluster self-diagnostic mode, turn the ignition switch OFF, or press and hold the SELECT/RESET button for three or more seconds after all fault codes and GAGE test results have been displayed, then release the buttons.

CHRYSLER INSTRUMENT CLUSTER SELF-CHECKS

On older Chrysler electronic instrument display clusters that have a tachometer, the self-diagnostic sequence is initiated by pressing the TRIP and TRIP RESET buttons simultaneously, turning the ignition on, then releasing the buttons. On those without a tach, press STEP and U.S./MET buttons simultaneously. If nothing happens, the cluster is bad. The odometer should display EIC indicating the cluster is ready to begin the self tests.

To begin the first 5 tests, press the U.S./MET button. All vacuum fluorescent displays should illuminate. If the number 1, 2 or 3 displayed on the speedometer, there is a fault in the speedometer and the cluster needs to be replaced. A fault code 4 indicates a problem in the odometer memory chip (only the chip has to be replaced). When the number 5 appears, the cluster has passed the first five tests.

To sequence through the next 3 tests, you have to press the U.S./MET button each time. The sixth test illuminates all the individual display segments and flashes a 6 when complete. Test 7 lights up all the gauge scales and symbols and flashes a 7 when complete. Test 8 lights up the warning lamps in sequence and flashes an 8 when through. If the cluster passes all 8 tests, then the problem is outside the cluster.

If you have a Chrysler dash where the fuel, temp and oil gauges all read maximum and remain there after the engine has started, check for a loose module connector on the back of the cluster.

If the speedometer and odometer do not work, check the operation of the "distance sensor" (speedometer sending unit) on the transaxle with an ohm meter. Set the scale so that readings of less than one ohm will be shown clearly. Connect the meter to the sensor terminals and turn it. A good sensor should produce eight distinct pulses of 0.5 ohms or less with every revolution. Do not use a test light on the sensor as doing so may damage it.

CAN ELECTRONIC INSTRUMENT CLUSTERS BE REPAIRED?

Electronic instrumentation is fairly reliable, but from a service perspective, either it works or it does not. There is nothing in between. It makes no difference if the entire cluster is dead or of only one gauge or display is acting up. In most instances, vehicle manufacturers have made no provisions for "field servicing" or repairing an instrument cluster if it is defective. You have to replace the entire unit with a new unit or a used unit from a salvage yard, or find a source online that repairs electronic clusters.

The only components that you can generally replace yourself are dash light bulbs. But some of these are now an integral part of the circuit board (the turn signal indicators, for example) and cannot be replaced if they fail.

Even if you are an electronics wizard who knows how to test and replace individual circuit components, the vehicle manufacturers have not made the necessary service information available to the aftermarket. So for most of us, the only practical alternative is to replace the cluster if it has an internal problem, or send it to someone who specializes in this type of repair work.

electronic instrument cluster
INSTRUMENT CLUSTER REPLACEMENT TIPS

Tearing apart a dash to extract the instrument cluster is fairly easy on some vehicles, and a major ordeal on others. The best advice is to buy an AlldataDIY subscription for your vehicle BEFORE you tear into the dash, and look up the step-by-step replacement procedure for the cluster. This way, there wont be any surprises, and youll have an idea of whats involved BEFORE you start the disassembly.

WARNING: Always disconnect the battery BEFORE you begin any electrical work. This will eliminate the risk of accidentally shorting any wires that might cause electrical damage or start a fire. It will also disable the airbag circuit so the air bag is not accidentally triggered.

RESETTING THE ODOMETER

Most states have laws regarding odometer tampering, so if the electronic instrument cluster in your vehicle has an electronic odometer and memory chip, the memory chip must be transferred to the new cluster. What happens if you forget or lose the original odometer chip? You are supposed to put a sticker on the door certifying the date and mileage that a new zeroed odometer was installed. The vehicle manufacturer may also be able to supply you with a replacement odometer chip that is programmed with your old mileage (if possible).

There are also federal laws that prohibit odometer tampering. The Federal Truth in Mileage Act (TIMA) requires vehicle sellers to provide actual, truthful odometer readings and to disclose any known inaccuracies. TIMA makes odometer fraud a felony. Failure to disclose that an odometer has been changed or repaired (altered in any way) and/or falsifying mileage documentation will result in fines and/or imprisonment.

Digital odometers can be reprogrammed to change the mileage. Some electronic cluster repair companies can do this for you, but require a signed statement as to your vehicle's actual mileage. Some new car dealers can also use an authorized factory scan tool to reset the odometer in a replacement instrument cluster to the vehicle's actual mileage after an instrument cluster has been replaced. You can also buy software online that hacks into a digital odometer and allows you to reset the mileage reading. Be warned, however, that rolling back the mileage to make your vehicle appear to have less wear and tear than it actually has can get you into hot water if you later sell the vehicle and are caught trying to cheat someone. Used car buyers will often use CARFAX or a similar service to check a vehicle's history, including its mileage.

 

Back to Electrical Battery Starting Charging System   |    Back to Info Main Page

Post your Comment
  - no <, >, [ or ] tags will go through. URL will be converted to link

Total messages: 0